Improvement of Formability by Oscillation of Internal Pressure in Pulsating Hydroforming of Tube

A new history of internal pressure in the hydroforming processes of tubes is developed to attain high formability. The effect of improvement of formability by the oscillation of internal pressure in a pulsating hydroforming process of tubes is examined using both finite element simulation and experiment. The deformation behaviour during the hydroforming is greatly affected by the oscillation of internal pressure. For a monotonic history of small internal pressure, the wrinkling was caused by insufficient bulging, whereas the necking and bursting occurred for a monotonic history of large internal pressure. The occurrence of these defects can be avoided by oscillating the internal pressure in the pulsating hydroforming. The improvement of formability in the pulsating hydroforming is due to both low pressure and oscillation of pressure. The effects of the amplitude and cycle number of pressure in the pulsating hydroforming on the deformation behaviour are investigated. It is found the oscillation of internal pressure is effective in preventing the occurrence of defects.     

Relation between crystal structure and lattice oxygen content of sintered reaction-bonded silicon nitride

When reaction-bonded silicon nitride containing MgO/Y₂O₃ additives is sintered at three different temperatures to form sintered reaction-bonded silicon nitride (SRBSN), the thermal conductivity increases with sintering temperature. The β-Si₃N₄ (silicon nitride) crystals of SRBSN ceramics were synthesized and characterized to investigate the relation between the crystal structure and the lattice oxygen content. The hot-gas extraction measurement result and the crystal structure obtained using Rietveld analysis suggested that the unit cell size of the β-Si₃N₄ crystal increases with the decrease in the lattice oxygen content. This result is reasonable considering that the lattice oxygen with the smaller covalent radius substitutes nitrogen with the larger one in the β-Si₃N₄ crystals. The lattice oxygen content decreased with increasing sintering temperature which also correlated with increase in thermal conductivity. Moreover, it is noteworthy from the viewpoint that it may be possible to apply the lattice constant analysis for the nondestructive and simple measurement of the lattice oxygen content that deteriorates the thermal conductivity of the β-Si₃N₄ ceramics.     

One-Step Generation of Multiple Gene-Edited Pigs by Electroporation of the CRISPR/Cas9 System into Zygotes to Reduce Xenoantigen Biosynthesis

Xenoantigens cause hyperacute rejection and limit the success of interspecific xenografts. Therefore, genes involved in xenoantigen biosynthesis, such as GGTA1, CMAH, and B4GALNT2, are key targets to improve the outcomes of xenotransplantation. In this study, we introduced a CRISPR/Cas9 system simultaneously targeting GGTA1, CMAH, and B4GALNT2 into in vitro-fertilized zygotes using electroporation for the one-step generation of multiple gene-edited pigs without xenoantigens. First, we optimized the combination of guide RNAs (gRNAs) targeting GGTA1 and CMAH with respect to gene editing efficiency in zygotes, and transferred electroporated embryos with the optimized gRNAs and Cas9 into recipient gilts. Next, we optimized the Cas9 protein concentration with respect to the gene editing efficiency when GGTA1, CMAH, and B4GALNT2 were targeted simultaneously, and generated gene-edited pigs using the optimized conditions. We achieved the one-step generation of GGTA1/CMAH double-edited pigs and GGTA1/CMAH/B4GALNT2 triple-edited pigs. Immunohistological analyses demonstrated the downregulation of xenoantigens; however, these multiple gene-edited pigs were genetic mosaics that failed to knock out some xenoantigens. Although mosaicism should be resolved, the electroporation technique could become a primary method for the one-step generation of multiple gene modifications in pigs aimed at improving pig-to-human xenotransplantation.     

Phase diagram for the helical texture in 3He-A

The stability region of the helical textures in³He-A in thev _s-H phase diagram is theoretically determined. Herev _sis the superflow velocity andH (v _s) is the external magnetic field. The pitch of the helixk ^–1 that minimizes the Gibbs free energy and the corresponding inclination angles ofl andd are determined numerically as functions ofv _sandH. The NMR frequencies (two longitudinal and four transverse frequencies) associated with the helical texture are obtained.Work supported by the National Science Foundation under Grant No. DMR 76-21032.     

Effect of polymer density on polyethylene hollow fiber membrane formation via thermally induced phase separation

Microporous high‐density polyethylene (HDPE) and low‐density polyethylene (LDPE) hollow fiber membranes were prepared from polyethylene–diisodecyl phthalate solution via thermally induced phase separation. Effect of the polyethylene density on the membrane structure and performance was investigated. The HDPE membrane showed about five times higher water permeability than the LDPE membrane because it had the larger pore and the higher porosity at the outer membrane surface. The formation of the larger pore was owing to both the initial larger structure formed by spinodal decomposition and the suppression of the diluent evaporation from the outer membrane surface due to the higher solution viscosity. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 471–474, 2004     

Two-stage pyrolysis of heavy oils. 3. Pyrolysis of tar-sand bitumens. Relation between ethylene yield and structural characteristics of heavy oils

Thermal cracking of tar-sand bitumens has been carried out using a two-stage pyrolysis reactor with temperature zones of 440°C and 750–800°C, respectively. Feedstocks were pyrolysed in the first stage into cracked oils, which were carried to the second stage for subsequent pyrolysis. Only 12–14 wt% of ethylene was obtained from tar-sand bitumens at the residence time of 1.2 s in the second stage, although 27 and 16 wt% were obtained from Taching and Iranian heavy vacuum residues, respectively. The tar-sand bitumens contain shorter paraffinic straight-chains and have more branched molecules than the vacuum residues of petroleum. A straight-chain paraffin index is proposed, with which a good correlation was obtained between ethylene yield and the fraction of straight-chain paraffin carbons in the heavy oil.     

Studies on phase separation rate in porous polyimide membrane formation by immersion precipitation

Phase separation rate during porous membrane formation by immersion precipitation was investigated by light scattering in a polyimide/N‐Methylpyrrolidone (NMP)/water system. In the light scattering measurement, plots of scattered intensity against scattered angle showed maxima in all cases, which indicated that phase separation occurred by a spinodal decomposition (SD). Characteristic properties of the early stage of SD, such as an apparent diffusion coefficient D_app and an interphase periodic distance Λ, were obtained. The growth process of Λ was also followed by light scattering. The growth rate had the same tendency as D_app when water content in the nonsolvent bath and the polymer concentration in the cast solution were changed. The pore size of the final membrane increased with decreasing water content, which was opposite to the tendency of Λ growth rate. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 292–296, 2003     

Photocatalytic Activity of a TiO<Subscript>2</Subscript> Photocatalyst Doped with C<Superscript>4+</Superscript> and S<Superscript>4+</Superscript> Ions Having a Rutile Phase Under Visible Light

C⁴⁺ and S⁴⁺-codoped titanium dioxide (TiO₂) having a rutile phase was prepared. By doping C⁴⁺ and S⁴⁺ ions into a TiO₂ lattice, the absorption edge of rutile TiO₂ powder was largely shifted from 400 to 700 nm. 2-Methylpyridine and methyleneblue were photocatalytically oxidized at high efficiency on C⁴⁺ and S⁴⁺-doped TiO₂ under visible light at a wavelength longer than 5 nm.     

Porous cellulose acetate membrane prepared by thermally induced phase separation

Microporous cellulose acetate membranes were prepared by a thermally induced phase separation (TIPS) process. Two kinds of cellulose acetate with acetyl content of 51 and 55 mol % and two kinds of diluents, such as 2‐methyl‐2,4‐pentandiol and 2‐ethyl‐1,3‐hexanediol, were used. In all polymer‐diluent systems, cloud points were observed, which indicated that liquid–liquid phase separation occurred during the TIPS process. The growth of droplets formed after the phase separation was followed using three cooling conditions. The obtained pore structure was isotropic, that is, the pore size did not vary across the membrane. In addition, no macrovoids were formed. These pore structures were in contrast with those usually obtained by the immersion precipitation method. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 3951–3955, 2003